Commercial Mowers | 1550 TerrainCut™ Front Mowers

Features

Diesel engine has high-quality features to minimize operating cost

Hood open for access to engine

3-cylinder, liquid-cooled diesel engine

The 1500 Series TerrainCut™ Front Mowers are powered by liquid-cooled, 3-cylinder diesel engines.

These engines feature low levels of exhaust and emissions, reduced noise levels, and excellent fuel economy. They also meet the necessary Environmental Protection Agency (EPA) Tier 4 emissions requirements.

The 1570, 1575, 1580, and 1585 models are biodiesel compatible from the factory up to B20. The 1550 model requires an optional kit to be compatible with B20 biodiesel fuel.

Engine drawing for 1570, 1575, 1580, and 1585

	1550	1570, 1575, 1580, 1585
Fuel	Diesel (optional kit permits B20 compatibility)	Diesel (B20 compatible)
Gross power at maximum rpm	25 hp (18.4 kW), PS	37.4 hp (27.5 kW), PS
Displacement	77 cu in. (1.262 L)	100.2 cu in. (1.642 L)

Key features of the engine include:

Economical cast-in block cylinder design for good cooling and long life
Indirect fuel injection (1550)
Direct fuel injection (1570, 1575, 1580, 1585)
- Injects fuel directly on top of pistons for more efficient combustion
- Delivers more horsepower per gallon of fuel
- Improves starting
- Develops more horsepower per gallon of fuel and improves starting
Aluminum alloy pistons with built-in steel struts are lightweight to reduce connection rod bearing loads and provide good heat transfer characteristics
Design permits tighter tolerances and neutralizes expansion of the piston, thereby reducing blow-by gas and noise from the piston slap
Higher top rings on the piston and a thinner head gasket greatly reduce the volume of unburned waste gases and increase combustion efficiency
Timing gears and injector drive gears utilize helical profile gears to help lower engine noise; gear teeth have a newly designed roll-off profile, giving almost no clash, no noise, and no backlash
Fuel filter with replaceable element
Full-pressure intake manifold provides quick starts in temperatures down to 0°F (-18°C) (optional engine coolant heater attachment assists starting under more extreme conditions)
Auto-bleed fuel system – there is no need to prime the system if the tractor runs out of fuel; the system self-primes the injection pump, lines, and injectors, providing fast fuel recovery
Key start and shutoff eliminates fuel shut-off knob; electric solenoid shuts fuel supply off immediately when key is turned off
See-through coolant recovery tank permits operator to check coolant level without removing radiator cap
Enclosed engine compartment to keep out debris and lower sound levels
Sealed radiator compartment to keep trash and debris on outside of hood
Excellent torque for plenty of lugging power when operating in tough mowing conditions
Full-pressure lubrication for positive lubrication, even when operating on slopes
Dual-element, dry-type, replaceable air cleaner completely sealed for effective cleaning
- 90 percent to 95 percent of dirt ejected before it reaches the paper element
Secondary safety element for additional filtering
Progressive-type air restriction indicator to let operator know when the filter needs servicing
Automotive-type alternator for plenty of charge to the battery and power for accessories
- 75 amp for open-station models
- 95 amp for ComfortCab models
Automatic initiation of air heater for easier cold-weather starting
Automotive-sensing system tells operator when engine is ready to start

Rear-mounted radiators

Rear-mounted radiators (1550, 1570, 1580)

Rear-mounted radiators and air conditioner condenser (1575, 1585)

Fuel tank is large capacity with convenient gauge for maximum uptime

Fuel tank

Fuel gauge (shown on 1585)

Fuel tank features:

16-U.S. gal. (60.6-L) capacity provides a 10-hour run time.
Top draw provides clean fuel.
Fuel indicator is conveniently located.

Mower decks for TerrainCut™ Front Mowers match a wide variety of needs

Since 1998 the John Deere 7-Iron™ mower deck has demonstrated commercial quality, performance, and durability. The 7-Iron PRO, FastBack™, and FastBack PRO mower decks deliver an even higher-quality cut in even more diverse conditions.

1580 TerrainCut Front Mower with 72-in. (183-cm) FastBack PRO Mower Deck

1575 TerrainCut Front Mower with 72-in. (183-cm) 7-Iron PRO Mower Deck

TerrainCut Front Mower Compatibility

Mower Deck	1550	1570	1575	1580	1585
60-in. (152-cm) 7-Iron PRO Side-Discharge Mower Deck	X	X	X*	X*	X*
62-in. (157-cm) FastBack Rear-Discharge Mower Deck	X	X	X	X	X
72-in. (183-cm) 7-Iron PRO Side-Discharge Mower Deck	X	X	X	X	X
72-in. (183-cm) FastBack PRO Rear-Discharge Mower Deck	X	X	X	X	X

Rear weights (UC13263) are required based on machine configuration. Must also order TCB10303, rear weight mounting bracket.

*Mower deck offset for trimming capability. Vehicle track width is 2 in. (5.1 cm) wider on the discharge side of deck. This may cause the tire to drive over uncut grass on discharge side of deck.

NOTE: These mower decks will not retrofit to F900 Series or F1145 Front Mowers.

Rotate for Service (RFS™)

Mower deck showing RFS feature

Rotate for Service (RFS) feature provides access for cleaning and maintenance of the mower decks:

The rotation angle will vary depending on deck size and power unit tire size.
No tools are required to access belts.
The underside of the mower deck is easy to access.
Easy on/off design simplifies installing and removing mower decks.
Top, greaseable spindles can be accessed without removing belt covers.

The Rotate for Service position also reduces the length of the machine for trailering.

Certification

TerrainCut Front Mowers comply with ANSI B71.4 safety certification.

Heavy-duty blade spindles

Cast-iron spindle housing

The mower spindle housings are made of ductile cast iron.

Key benefits of ductile cast-iron spindle housings:

Ductile cast-iron material provides superior impact strength.
Gusseted design puts reinforcement where it is needed.
Strength of cast iron protects against damage from blade impacts.
Grease fitting is mounted at the top for easy access.
Grease pressure-relief valve minimizes seal damage from overfilling with grease and keeps debris from entering housing.
The 8-in. (20.3-cm) diameter housing distributes loads and impacts to minimize deck-shell damage.
Spindle allows ability to be rebuilt.

NOTE: The 72-in. (183-cm) 7-Iron V-Flex Side-Discharge Mower Deck has an aluminum center spindle housing. The outside blades are driven by cast-iron gearboxes.

60-in. (152-cm) 7-Iron PRO Side-Discharge Mower Deck

60-in. 7-Iron PRO Mower Deck

Features include:

Blade tip speed of 18,000 fpm (5486 m/min) for more blade strikes per inch mowed.
Trim-edge bumper reduces damage to the mower deck and property.
Redesigned front baffle manages airflow and controls clippings better.
Blade spindle housings are made of ductile cast iron
- Gusseted design puts reinforcement where it is needed.
Spindle pocket reinforcement gives even greater structural durability.
Adjustable anti-scalp wheels help smooth out the mowing job.
Standard semi-pneumatic caster tires will not go flat from punctures.

The mower is designed to provide exceptional cut quality at higher travel speeds:

The mower deck is stamped from 7-gauge, 0.179-in. (4.6-mm) steel to minimize the number of welds and provide a smooth underside, with fewer sharp corners, for reduced material buildup.
- Provides precision components and long deck life
- Single piece of steel means no welds to break
- Provides a smooth underside, without corners, reducing material buildup
0.75-in. (1.9-cm) solid steel bar is welded to mower deck perimeter for added strength.
The rounded corners of the stamped deck help distribute impact stress to reduce the potential of damage when the mower contacts trees, rocks, curbs, and other fixed obstacles.
A deep-deck design of 5.5-in. (14-cm) delivers excellent airflow so material can be processed quickly and efficiently.
1-in. to 6-in. (2.5-cm to 12.7-cm) cutting heights, in 0.5-in. (1.3-cm) increments, allow the operator to match all mowing conditions.

Unique baffling system allows grass to stand up before being cut, producing a uniform length and appearance:

Baffling system eliminates clumping, blowout, and windrowing.
Wide discharge opening provides even clipping dispersal for an excellent, finished appearance in all conditions.

62-in. (157-cm) FastBack Mower Deck

62-in. FastBack Mower Deck

The 62-in. (157-cm) FastBack rear-discharge mower is ideally suited for:

Areas where people are present
- Schools
- Parks
- Playgrounds
- Traffic areas (city boulevards, roadsides, etc.)
Conditions and applications:
- Areas with long grass and weeds
- Areas where customer is not as concerned about having a wide dispersal of grass (park areas, roadsides, etc.)
Government bids that specify a rear discharge mower.

Key features of the 62-in. (157-cm) Rear-Discharge Mower Deck include:

Mower deck is constructed of 7-gauge, 0.179-in. (4.6-mm) steel for the strength to stand up to the demanding use of commercial and municipal mowing applications.
Blade spindle housings are made of ductile cast iron.
- Gusseted design puts reinforcement where it is needed.
Deck is constructed with a unique baffling system that reduces clumping and windrowing and produces a finished appearance that competitive rear-discharge mowers cannot match.
The belt-drive system has an easy-to-adjust tension device.
- By using a spring system, the risk for over tensioning is eliminated, ensuring a long belt life and excellent performance during the season.
For easy service and maintenance, the deck can be rotated into the vertical locked service position.
Deep-deck design increases airflow so more material can be processed.
Operator can trim with either side.
- Dual side trimming increases operator productivity.
1-in. to 6-in. (2.5-cm to 15.2-cm) cutting heights, in 0.5-in. (1.3-cm) increments, allow the operator to match all mowing conditions.
Gauge wheels, rollers, or side-mounted skid shoes lift the deck over uneven surfaces for a well-groomed appearance.
Double-captured anti-scalp wheels provide increased durability.
Easy lift and lock system for service purposes.
Standard semi-pneumatic caster tires will not go flat when punctured.
Spindles can be greased without removing belt shields.
1-in. (2.5-cm) cold-forged spindles are strong for long life.
- Heat-treated to provide additional strength
Certified to European (CE) standards

72-in. (152-cm) 7-Iron PRO Side-Discharge Mower Deck

72-in. 7-Iron Pro Side-Discharge Mower Deck

Features include:

Blade tip speed of 18,000 fpm (5486 m/min) for more blade strikes per inch mowed.
Trim-edge bumper reduces damage to the mower deck and property.
Redesigned front baffle manages airflow and controls clippings better.
Spindle pocket reinforcement gives even greater structural durability.
Blade spindle housings are made of ductile cast iron.
- Gusseted design puts reinforcement where it is needed.
Adjustable anti-scalp wheels help smooth out the mowing job.
Standard semi-pneumatic caster tires will not go flat from punctures.

The mower is designed to provide exceptional cut quality at higher travel speeds:

The mower deck is stamped from 7-gague, 0.179-in. (4.6-mm) steel to minimize the number of welds and provide a smooth underside, with fewer sharp corners, for reduced material buildup.
- Provides precision components and long deck life
- Single piece of steel means no welds to break
- Provides a smooth underside, without corners, reducing material buildup
0.75-in. (1.9-cm) solid steel bar is welded to mower deck perimeter for added strength.
The rounded corners of the stamped deck help distribute impact stress to reduce the potential of damage when the mower contacts trees, rocks, curbs, and other fixed obstacles.
A deep-deck design of 5.5-in. (14-cm) delivers excellent airflow so material can be processed quickly and efficiently.
1-in. to 6-in. (2.5-cm to 12.7-cm) cutting heights, in 0.5-in. (1.3-cm) increments, allow the operator to match all mowing conditions.

Unique baffling system allows grass to stand up before being cut, producing a uniform length and appearance:

Baffling system eliminates clumping, blowout, and windrowing.
Wide discharge opening provides even clipping dispersal for an excellent, finished appearance in all conditions.

72-in. (183-cm) FastBack PRO Mower Deck

72-in. FastBack PRO Mower Deck

The 72-in. (183-cm) Rear-Discharge FastBack PRO Mower Deck is ideally for professional landscapers and government municipalities requiring rear discharge placement of grass and debris, John Deere FastBack PRO rear-discharge mower decks deliver a commercial mowing solution. Advantages of a rear-discharge mower include:

Less chance of damage from objects being thrown from the mower deck
Time savings with the ability to mow closely around fixed objects with either side of the deck
A cleaner mowing experience by lessening the amount of debris that can blow onto the operator

A rear-discharge mower deck is ideally suited for:

Schools
Parks
Playgrounds
Traffic areas (city boulevards, roadsides, etc.)
Areas with long, grassy spots that need to be cut, where you are not as concerned about wide dispersal of grass (park areas, roadsides, etc.)
Some government bids specify that the mower is equipped with a rear discharge.

Key features of the 72-in. (183-cm) Rear-Discharge Mower Deck include:

Mower deck is constructed of 7-gauge, 0.179-in. (4.6-mm) steel for the strength to stand up to the demanding use of commercial and municipal mowing applications.
Blade spindle housings are made of ductile cast iron.
- Gusseted design puts reinforcement where it is needed.
Deck is constructed with a unique baffling system that reduces clumping and windrowing and produces a finished appearance that competitive rear-discharge mowers cannot match.
Operator can trim with either side.
- Dual side trimming increases operator productivity.
- Trim-edge bumpers on each side reduces damage to the mower deck and property.
The belt-drive system has an easy-to-adjust tension device.
- By using a spring system, the risk for over tensioning is eliminated, ensuring a long belt life and excellent performance during the season.
For easy service and maintenance, the deck can be rotated into the vertical locked service position. Deep-deck design increases airflow so more material can be processed.
1-in. to 6-in. (2.5-cm to 15.2-cm) cutting heights, in 0.5-in. (1.3-cm) increments, allow the operator to match all mowing conditions.
Gauge wheels or rollers lift the deck over uneven surfaces for a well-groomed appearance.
Double-captured anti-scalp wheels provide increased durability. Easy lift and lock system for service purposes.
Standard semi-pneumatic caster tires will not go flat when punctured. Spindles can be greased without removing belt shields.
1-in. (2.5-cm) cold-forged spindles are strong for long life.
- Heat-treated to provide additional strength
Certified to European (CE) standards

Mower deck specifications

	60-in. (152-cm) 7- Iron PRO Side- Discharge	62-in. (157-cm) FastBack Rear- Discharge	72-in. (183-cm) 7- Iron PRO Side- Discharge	72-in. (183-cm) FastBack PRO Rear- Discharge
Gauge (thickness)	7 gauge, 0.179 in. (4.6 mm)	7 gauge, 0.179 in. (4.6 mm)	7 gauge, 0.179 in. (4.6 mm)	7 gauge, 0.179 in. (4.6 mm)
Cutting height	1 to 6 in. (2.5 to 15.2 cm)	1 to 6 in. (2.5 to 15.2 cm)	1 to 6 in. (2.5 to 15.2 cm)	1 to 6 in. (2.5 to 15.2 cm)
Caster wheel type	Semi-pneumatic	Semi-pneumatic	Semi-pneumatic	Semi-pneumatic
Gauge wheels	Yes, front and rear	Yes, front and rear	Yes, front and rear	Yes, front and rear
Deck oscillation relative to ground plane	+/- 15 degrees	+/- 15 degrees	+/- 15 degrees	+/- 15 degrees
Lateral deck tilt	+/- 8 degrees	+/- 8 degrees	+/- 8 degrees	+/- 8 degrees
Deck installed at factory	No	No	No	No
Time required for one person to install or remove deck (without tools)	10 minutes	10 minutes	10 minutes	10 minutes
Time to change height of cut	3 minutes without tools	3 minutes without tools	3 minutes without tools	3 minutes without tools
Belt type	Kevlar belt	Kevlar belt	Kevlar belt	Kevlar belt
Belt shield type	Plastic	Plastic	Plastic	Plastic
Belt shield time to remove or install	2 minutes or less	2 minutes or less	2 minutes or less	2 minutes or less
Blade type	High lift	Medium lift	High lift	Medium lift
Blade tip speed	18,000 fpm (5,486 m/min)	16,000 fpm (4,877 m/min)	18,000 fpm (5,486 m/min)	18,000 fpm ( 5,486 m/min)
Spindles	3	3	3	3
Spindle-housing material	Ductile cast iron	Ductile cast iron	Ductile cast iron	Ductile cast iron
Deck level laterally when raised	Yes	Yes	Yes	Yes
Discharge	Side	Rear	Side	Rear
Mowing width	60 in. (152 cm)	62 in. (157 cm)	72 in. (183 cm)	72 in. (183 cm)
Overall width (chute down)	74 in. (188 cm)	64 in. (163 cm)	86 in. (218 cm)	74 in. (188 cm)
Weight	---	---	---	---

PTO shaft drive is easy to access for quick-change of equipment

Front mower PTO shaft drive

Live, independent power take-off (PTO) powers a mower deck, rotary broom, or two-stage snow blower:

PTO can be engaged or disengaged on the go for greater productivity.
Hydraulic PTO clutch has delay relief valve for soft engagement.
Wet clutch design provides long life.
PTO is easily accessible.

Tires are matched to the machine size and mower widths

1550, 1570, 1575 tires

Tires

Standard drive tires:

23x10.5-12 or 23x8.5-12 (1550, 1570)
23x10.5-12 (1575)

Available steering tires: 18x8.5-10 (4WD) or 18x8.5-8 (2WD)

1580, 1585 tires

Standard drive tires: 26x12-12, 6 PR drive tires (1580, 1585)

Standard steering tires: 20x10.00-10, 6 PR steering tires (1580, 1585)

Optional mulching kits add versatility to the mower decks

Typical mulch kit shown

Kits are available to convert the 60-in. (152-cm) and 72-in. (183-cm) 7-Iron™ PRO Side-Discharge Mower Decks into mulching decks for use in grass and leaves.

The mulch kits include mulching blades, baffles, end covers, and attaching hardware.

Easy-to-operate controls maximize productivity

1570 TerrainCut™ Front Mower

1585 TerrainCut Front Mower

Maneuverability:

Turn radius of 13 in. (33 cm)
Uncut circle of 28 in. (71.1 cm) with a 72-in. (183-cm) 7-Iron™ PRO mower deck
Deck offset and pulled rearward
Tail-follows-the-trail trimming capability with 72-in. (183-cm) side-discharge mower deck
Steered wheels (tail) stay within the path (trail) cut by the mower deck, allowing maneuverability without the rear of the machine contacting mowing obstacles

Operator controls (1570 shown)

Master stop brake/directional foot pedals

Hydrostatic power steering provides the following benefits:

Makes it easy to turn the unit for less operator fatigue
Allows quick turns - two turns lock to lock - for excellent productivity

The steering console offers the following:

Throttle
Key switch
Headlight switch
T4 display for monitoring performance (1570, 1575, 1580, 1585)

Transmission controls, range lever, and on-demand four-wheel drive (4WD) lever (1585 shown)

Controls including levers for double-spool auxiliary hydraulic kit (1585 shown)

Console information/warning lights include the following:

Hour meter
Battery discharge light
Engine oil pressure
Engine coolant temperature
Hydraulic oil over temperature
Air preheater
Lights
Power take-off (PTO) operation indication

Two-pedal foot control

Two-pedal foot control:

Allows the operator to select speed and direction with just the touch of a toe
Keeps both hands free for steering and operating controls

Master stop brake (parking brake):

Provides stopping power to both drive wheels
Disengages the power take-off (PTO)
Disengages the optional cruise control
Used also for a parking brake

Individual turn-assist brakes and differential lock

Individual turn-assist brakes:

Provides additional traction when operating on hillsides
Ideal for tight trimming situations
Works in conjunction with hydrostatic foot controls to stop or slow the unit for turns

Differential lock:

Locks both front drive wheels together for added traction
Easily engaged with the left foot

4WD lever (1570 shown)

Deck lift-control lever

The 4WD control lever is standard on 1575, 1580, and 1585; it is a factory-installed option on the 1550 and 1570.

The 4WD control lever:

Allows the operator to select between on-demand or full-time 4WD on 1550, 1570, and 1575 models
Allows the operator to select between on-demand or full-time 4WD and full-time two-wheel drive (2WD) on 1580 and 1585 models

Electronic cruise control (optional):

Beneficial when mowing open areas or when transporting

The lift-control lever is conveniently located within easy reach of the operator's right hand.

Tilt steering

Tilt steering column (1550 shown)

Tilt steering column allows the operator to adjust to the most comfortable position:

Allows additional clearance for platform entry and exit
Over 15 in. (38.1 cm) of travel
Works in conjunction with the seat to accommodate all operators, regardless of size

1585 shown with control levers for double-spool auxiliary hydraulic kit

A two-speed transaxle shift lever is standard on 1580 and 1585.

Safety starting system helps protect the operator and others

1550 mowing grass

TerrainCut™ Front Mowers have an operator-presence system.

To start the engine the following conditions must be met:

Master brake must be depressed or the parking brake locked; the hydrostatic foot controls will then be in the neutral position.
PTO must be disengaged
Ignition key must be used.

In addition, once the engine is running, an interlock automatically shuts the engine and PTO off if the operator leaves the seat. To keep the engine running, the operator must disengage the PTO and set the parking brake before dismounting.

Tilt steering and headlights are standard equipment

Three-piece steering column

The three-piece steering column provides the following:

Easy access to the steering valve and electrical components
Better fit-up and appearance
Easy adjustment to accommodate all operators
Standard 50-W halogen headlights

Brakes and differential lock are convenient to use for maximum productivity

Wet-disk brakes/differential lock

Wet-disk brakes are standard equipment:

Provide positive stopping power and long life
Require minimal adjustment
Individual turn brakes are located on left side of platform

The differential lock is also included as standard equipment:

Locks both front drive wheels together for extra traction, when needed
Conveniently located pedal to allow the operator to engage the differential lock with the left foot while maintaining speed and direction (forward or reverse) with the right foot

12-V power outlet is convenient to use

12-V power outlet

The 12-V power outlet can be used to recharge radios and cell phones, popular tools used by commercial cutters.

The outlet is conveniently located under the front of the seat.

Certification ensures compliance with safety standards

Rollover protective structure (ROPS)

TerrainCut Front Mowers comply with ANSI B71.4 2004 safety certification specification.

The ROPS complies with the U.S. Occupational Safety and Health Administration (OSHA) 1928.51 standard for rollover protection.

Front mower seats have standard suspension with arm rests for added comfort and productivity

Standard comfort-adjust suspension seat

Optional air-suspension seat

Operator comfort enhances productivity. TerrainCut™ Front Mowers include suspension seats with green accents and an embroidered John Deere logo. The comfort-adjust mechanical spring suspension seat is base equipment, and an air-suspension is an optional upgrade. The operator can adjust suspension by increasing or decreasing pressure for optimum comfort. Fore-aft adjustments accommodate both tall and short operators.

Both seats are 24-in. (61-cm) tall and include back-angle, lumbar, and arm rest adjustments. The eye-catching seats are constructed from two unique vinyl textures and sewn with decorative stitching. Retractable seat belts prevent belts from becoming tangled in the seat suspension and controls.

Other comfort features include:

Standard cup holder
Noise level meets North American and European standards

Manage your commercial mowing fleet using John Deere Operations Center™

TerrainCut™ Front and Wide-Area Mowers

ZTrak, QuikTrak, and commercial walk-behind Mowers

Overview

A JDLink™ M Modem - 4G connects a commercial mower to the John Deere Operations Center, which enables you to manage your fleet more efficiently, increase productivity, and reduce labor costs. With a modem and Operations Center, you are always connected to the work in progress and can make timely adjustments to keep your fleet mowing.

JDLink M Modem - 4G

A JDLink M Modem - 4G is standard equipment on model year 2024 and newer TerrainCut Front and Wide-Area Mowers.

A modem can be field installed on:

Model year 2024 and newer Z700 ZTrak™ Mowers
Model year 2024 and newer gasoline-powered Z900 ZTrak Mowers
Model year 2024 and newer Z994R ZTrak Mowers
Model year 2024 and newer Q800 QuikTrak™ Mowers
Model year 2025 and newer R Series commercial walk-behind mowers
Model year 2022-2023 TerrainCut Front Mowers
Model year 2023 TerrainCut Wide-Area Mowers

See compatibility section for serial number breaks and requirements.

John Deere Operations Center

John Deere Operations Center is available on PC, Apple iOS, and Android mobile apps

The John Deere Operations Center tracks your fleet and provides tools to analyze mower data. The connected features vary by mower model.

Models	Location and status	GPS speed	Geofencing and curfews	Engine hours	Maintenance planner	Machine Analyzer Tool	Fuel level	Fuel consumption	Diagnostic trouble codes	Service Advisor Remote
Z700 ZTrak Mowers	X	X	X	Key	X	X	---	---	---	---
Z900 ZTrak Mowers with carbureted engines	X	X	X	Key	X	X	---	---	---	---
Z900 ZTrak Mowers with EFI engines	X	X	X	Sync	X	X	X	X	X	X
Z994R ZTrak Mowers	X	X	X	Key	X	X	---	---	---	---
E Series QuikTrak Mowers	X	X	X	Key	X	X	---	---	---	---
Q820M, Q850M, and Q850R QuikTrak Mowers	X	X	X	Sync	X	X	X	---	X	---
Q865R EFI QuikTrak Mowers	X	X	X	Sync	X	X	X	X	X	X
R Series commercial walk-behind mowers	X	X	X	Key	X	X	---	---	---	---
1550 TerrainCut Front Mowers	X	X	X	Key	X	X	---	---	---	---
1570, 1575, 1580, and 1585 TerrainCut Front Mowers	X	X	X	Sync	X	X	---	X	X	X
1600 TerrainCut Wide-Area Mowers	X	X	X	Sync	X	X	---	X	X	X

Location and status

Operations Center map displaying past locations of a mower

Mobile view of Operations Center map showing GPS speed

The JDLink M Modem - 4G regularly transmits the location and operational status of each mower in the fleet so you can monitor mowing progress in Operations Center.

Location history-Display of map with current and past locations of each mower.
GPS Speed-Maps each mower’s current speed, based on GPS location data, so you can target operator training. GPS speed is only viewable on Apple iOS and Android mobile apps.
Geofencing-Alerts when a mower enters or exits a prescribed area, for example if the mower has been stolen or an operator entered an area that should not be mowed.
Curfews-Alerts if the mower is operating outside prescribed times, for example residential areas with early-morning noise restrictions.

Engine hours

The modem regularly transmits the mower’s engine hours to inform maintenance planning and balance use.

Sync-The mower reports actual engine hours to the Operations Center.
Key-Engine hours are estimated by monitoring the key switch. Engine hours can be corrected in Operations Center.

Maintenance planner

Operations Center Maintenance Planner

Factory or custom maintenance plans can be established in Operations Center. Maintenance alerts are sent when engine hours reach maintenance intervals.

Machine Analyzer Tool

Operations Center Machine Analyzer Tool

On select products, the modem reports the time the mower spent transporting, idling, and working. The Operations Center’s Machine Analyzer tool reports usage data which allows you to analyze operator behavior, identify causes of low productivity, and initiate corrective actions.

Fuel level

On select products, the modem reports the fuel level. On these products, an analysis of fuel consumption is available in the Operations Center Machine Analyzer Tool. Measuring fuel consumption enables you to address causes of excessive fuel use.

Diagnostic trouble codes (DTCs)

On select products, the modem transmits the trouble codes generated by the mower’s control units to the Operations Center. Addressing DTCs can reduce downtime and repair costs. For example, a low-engine oil pressure DTC can indicate an engine is low on oil. Addressing the issue can prevent costly downtime and repairs.

Service Advisor Remote

On select products, John Deere dealers can perform remote diagnostics, software programming, and adjustments without the cost of a service call.

Compatibility

A JDLink M Modem - 4G is standard equipment on model year 2024 and newer (SN 110,001-) TerrainCut Front Mowers and model year 2024 and newer (SN 690,001-) TerrainCut Wide-Area Mowers.

A JDLink M Modem - 4G can be field installed on the commercial mowing products listed below. Field installation attachments simplify modem installation, and include brackets, mounting hardware, harness, and instructions. Field installation requires a JDLink M Modem - 4G to be ordered separately.

Model	Compatible model years	Installation attachment
Z700 ZTrak Mowers	2024 and newer (SN 080,001-)	BUC11759
Gasoline-powered Z900 ZTrak Mowers	2024 and newer (SN 130,001-)	BUC11759
Z994R ZTrak Mowers	2024 and newer (SN 070,001-)	BUC11759
Z997R ZTrak Mowers	2021 and newer (SN 070,001-)	To be determined
QuikTrak Mowers	2024 and newer (SN 010,001-)	BUC11744
R Series commercial walk-behind mowers	2025 and newer (SN 070,001-)	BUC11918*
TerrainCut Front Mowers	2022-2023 (SN 080,001-110,000)	BUC11797
1600 TerrainCut Wide-Area Mowers	2023 (SN 680,001-690,000)	BUC11797

*Expected Spring of 2025

Serviceability is designed-in to reduce maintenance cost and increase uptime

Engine hood

Large screened area of engine hood

Hood latch

Engine hood includes large screened area:

Minimizes the amount of material that can get to the cooling radiators
Minimizes the need to clean the hood screens

Hood latch keeps the hood securely in place, providing an optimum seal:

A single hood latch is located on top of the hood behind the seat.

Engine hood opens to the rear

Designed-in service accessibility

Designed-in service accessibility helps ensure daily maintenance is completed to keep the machine operating at peak performance.

The hood opens rearward, exposing the following:

Engine
Oil and fuel filter
Hydraulic oil cooler
Radiator check/fill

The hood can be totally removed, if necessary. The seat flips forward for access to air filter, fuse bank, engine oil dipstick, and front of engine.

Condenser release knob

Condenser tilted back to permit cleaning

Easy-to-turn knobs are provided to release the air conditioning condenser (1575 and 1585 only) and fuel and hydraulic oil coolers so they can be tilted back to permit thorough cleaning between them and the engine coolant radiator.

Quick response (QR) codes link to owner information web pages

QR code label on control console

To speed access to owner information web pages, a QR code is printed onto a product identification number (PIN) label located on the control console near the seat. The owner information web pages that include links to:

Safety and how-to videos
Operator’s manuals
Parts catalogs
Maintenance reminder sheets
Attachments
Warranty statements

Foot platform access panel

Removable foot platform

The panel on the foot platform can be removed for access to the transaxle, PTO shaft, and most linkages.

Easy-to-read daily service decal is located on the bottom of the foot platform panel:

Provides access to easily hook up driveshaft when changing implements
Makes it more likely service will be performed at the optimum time, thus ensuring the highest level of performance and uptime

Panel on foot platform removed

Removal of the foot platform gives convenient access to the driveshaft that powers the mower deck, snow blower and rotary broom:

Helps make changing from one front implement to another easier and more convenient

Hydraulic hoses have reusable O-ring seal (ORS) fittings:

ORS fittings seal at a lower torque to prevent leaks.
Fittings can be removed from a damaged hose and installed on another hose.
Downtime and cost for repairs are reduced considerably.

Rotate For Service™ (RFS) feature shown

RFS service lockout latch

RFS feature provides access for cleaning and maintenance of the mower decks:

The service-latch pin allows mower deck to lock into position to ensure deck is held in position for cleaning or service.
The top-greaseable spindle grease fittings can be accessed without removing the belt covers.

Trailering features are included to reduce the time and cost to move equipment

Trailering features are designed-in for convenience:

Designed-in trailer tie-downs are located at the front and rear of the machine.
26-degree deck lift will clear the steepest trailer ramps for easy loading and unloading.
Rotate For Service™ (RFS) decks take up less room when transporting on trailers, allowing more room for other important equipment.

Remote battery posts

Remote battery posts simplify jump starting. Both positive and negative posts are located in front of the right rear steer tire.

Welded frame structure is made of high-strength steel

High-strength, tubular steel frame

The revolutionary tubular, high-strength welded steel frame provides durability and allows major components to be located lower in the machine:

The design results in a lower center of gravity for better stability and traction on hillsides and slopes.
Rollover protective structures (ROPS) are integral members of the frame.

Durable design

Durability features of the frame include:

Heat-treated cast-iron axles with 1.24-in. (3.15-cm) kingpins
Internal wet-disk brakes
Hydraulic PTO clutch, with brake
- Provides smooth engagement and long life
Hydrostatic oil cooler
O-ring seal (ORS) hydraulic fittings
Integrated, shaft-driven power take-off (PTO)
Sealed relays and electrical connectors
Heavy-duty, dual hydraulic cylinders
Nodular cast-iron lift arm sockets
Cast-iron rear bumper

Hydrostatic transmission and transaxle are heavy-duty to maximize uptime

Kanzaki 30-cc transmission

A Kanzaki® 30-cc transmission is used for reliable operation.

Durability features include the following:

High-capacity hydrostatic transmission and heavy-duty transaxle maximize performance and uptime and minimize cost of maintenance.
Charge pump is used to efficiently deliver oil to the transmission.
Oil cooler helps maintain optimum transmission oil temperature for superior performance and longer transmission life in the most challenging operating conditions.
Maximum forward top speed is 12 mph (19.3 km/h) on the 1550, 1570, and 1575 and 15 mph (24.1 km/h) on the 1580 and 1585.
Self-bleeding design helps keep air out of the system.

Kanzaki is a trademark of Kanzaki Kokyukoki Manufacturing Company.

Two-function mechanical rear-wheel drive for optimum use of the four-wheel drive feature

Mechanical rear-wheel drive axle

Mechanical rear-wheel drive is available as standard equipment (1575, 1580, 1585) or as a factory-installed option (1550, 1570):

On-demand four-wheel drive automatically engages and disengages as needed.
- Constantly maximizes trimming ability
- Offers better fuel economy than full-time four-wheel drive
- Provides better steering tire wear than full-time four-wheel drive
- Increases traction and trimming ability to allow a novice operator to mow like an expert
- Works in the forward direction only
Full-time four-wheel drive is on at all times.
- Can be engaged or disengaged on the go
- Provides maximum traction and flotation in poor conditions
- Works in reverse as well as the forward direction
Two-wheel drive position is available on 1580 and 1585 with two-speed transaxle.
- Disengages rear axle when transporting at high ground speeds

Dual drive tires are available to optimize performance in challenging conditions (1550 and 1570 only)

Dual drive tires

Dual 23x8.5-12 drive tires are available for increased hillside stability, flotation, and reduced ground compaction.

In addition, single drive tires may be set in the narrow or wide position to match mowing conditions.

NOTE: These tires are available for the 1550 and 1570 models only.

Tail-follows-the-trail design helps avoid obstacles in turns

Tail follows the trail

1585 TerrainCut™ Front Mower

Tail-follows-the-trail trimming with 72-in. (183-cm) mower decks. Steered wheels (tail) stay within the path (trail) cut by the mower deck, allowing maneuverability without the rear of the machine contacting mowing obstacles.

Maneuverability:

Turn radius 13 in. (33 cm)
Uncut circle – 28 in. (71cm) with a 72-in. (183-cm) 7-Iron PRO mower deck
- Deck offset for increased trim capability

Front mower ballast requirements

Front mowers must be properly ballasted for both good performance and safe operation. Ballast requirements differ depending on the front mower model and the implement being used.

The chart below gives the minimum ballast requirements for the various product configurations. Additional ballast is recommended for operating on slopes or other conditions that may warrant it.

NOTE: Use only implements and accessories recommended by the manufacturer.

Front mowers and current (model year 2015 and later) implements

TerrainCut™ 1500 Series Front Mowers
Product Configuration	60-in. (152- cm) Side- Discharge Deck (7- Iron™ PRO)	72-in. (183- cm) Side- Discharge Deck (7- Iron PRO)	62-in. (157- cm) Rear- Discharge Mower Deck	72-in. (183- cm) Rear- Discharge Mower Deck	60-in. (152- cm) HD Front Blade	47-in. (119- cm) HD Two-Stage Snow Blower	60-in. (152- cm) HD Two-Stage Snow Blower	60-in. (152- cm) Rotary Broom	43-in. (109- cm) Drop Spreader (Order Zone)
1550 Front Mower 2WD	1*	2*	1*	2*	0	2*	3*	1*	NA***
1550 Front Mower 4WD	0	1*	0	1*	0	2*	2*	0	Wide track
1570 Front Mower 2WD	1*	2*	1*	2*	0	2*	3*	1*	NA***
1570 Front Mower 4WD	0	1*	0	1*	0	2*	2*	0	Wide track
1575 Front Mower	Narrow track + 4 *	Wide track + 5*	Narrow track + 1 wheel weight on each side** + 3 weights* or wide track + 3 weights*	Wide track + 6*	1*	NA***	6*	Wide track + 1 wheel weight on each side** + 3 weights*	With 60-in. Rotary Broom: wide track + 2 wheel weight on each side** or with 60-in. Snow Blower: wide track
1580 Front Mower	0	1*	0	1*	0	NA***	2*	0	Wide track
1585 Front Mower	Narrow track + 4*	Wide track + 5*	Narrow track + 1 wheel weight on each side** + 3 weights* or wide track + 3 weights*	Wide track + 6*	1*	NA***	6*	Wide track + 1 wheel weight on each side** + 3 weights*	With 60-in. Rotary Broom: wide track + 2 wheel weight on each side** or with 60-in. Snow Blower: wide track
1400 and 1500 Series II Front Mowers
1420 Series II Front Mower	0	2*	1*	4*	6*	4*	6*	6*	NA***
1435 Series II Front Mower	0	2*	1*	4*	6*	4*	6*	6*	NA***
1445 Series II Front Mower	0	2*	1*	4*	6*	4*	6*	6*	NA***
1545 Series II Front Mower	0	2*	1*	4*	6*	NA***	6*	6*	NA***
1565 Series II Front Mower	0	2*	1*	4*	6*	NA***	6*	6*	NA***
1575/1585 Cab models: Rim design allows for tire assembly to be mounted in two different configurations, a narrow track or wide track width to meet ballast requirements.
*42-lb (19-kg) (UC13263) Quik-Tatch weight (installation requires TCB10303, rear weight mounting kit).
**50-lb (23-kg) front wheel weight(s) required (installation requires BM18101, mounting hardware kit).
***NA - Not recommended for use on front mower.
NOTE: Ballast requirements may change. Always refer to the implement owner's manual for the appropriate ballast requirements.

Front mowers and model year 2014 and prior implements

1400 and 1500 Series II Front Mowers
Product Configuration	60-in. (152- cm) Side- Discharge Deck (7- Iron™ and 7-Iron II)	72-in. (183- cm) Side- Discharge Deck (7- Iron and 7- Iron II)	62-in. (157- cm) Rear- Discharge Mower Deck	72-in. (183- cm) Rear- Discharge Mower Deck	MCS 600 Hydraulic Dump	Soft cab	Hard cab	60-in. (152-cm) HD Front Blade	47-in. (119-cm) HD Two- Stage Snow Blower	60-in. (152-cm) HD Two- Stage Snow Blower	60-in. (152- cm) Rotary Broom
1420 Series II Front Mower	0	1*	0	1*	0	0	0	6*	4*	6*	6*
1435 Series II Front Mower	0	1*	0	1*	0	0	0	6*	4*	6*	6*
1445 Series II Front Mower	0	1*	0	1*	0	0	0	6*	4*	6*	6*
1545 Series II Front Mower	NA	1*	NA	1*	0	0	0	6*	NA	6*	6*
1565 Series II Front Mower	NA	1*	NA	1*	0	0	0	6*	NA	6*	6*
1500 TerrainCut Front Mowers
1550 Front Mower 2WD	1*	2*	1*	2*	NA	NA	NA	0	2*	3*	1*
1550 Front Mower 4WD	0	1*	0	1*	NA	NA	NA	0	2*	2*	0
1570 Front Mower 2WD	1*	2*	1*	2*	NA	NA	NA	0	2*	3*	1*
1570 Front Mower 4WD	0	1*	0	1*	NA	NA	NA	0	2*	2*	0
1575 Front Mower	Narrow track + 4*	Wide track + 5*	Narrow track 1 wheel weight on each side** + 3 weights* or wide track + 3 weights*	Wide track + 6*	NA	NA	NA	1*	NA	6*	Wide track 1 wheel weight on each side** + 3 weights*
1580 Front Mower	0	1*	0	1*	NA NA		NA	0	NA	2*	0
1585 Front Mower	Narrow track + 4*	Wide track + 5*	Narrow track 1 wheel weight on each side** + 3 weights* or wide track + 3 weights*	Wide track + 6*	NA	NA	NA	1*	NA	6*	Wide track 1 wheel weight on each side** + 3 weights*
1575/1585 Cab models: Rim design allows for tire assembly to be mounted in two different configurations, a narrow track or wide track width, to meet ballast requirements.
* 42-lb (19-kg) (UC13263) Quik-Tatch weight (requires TCB10303, rear weight mounting kit).
** 50-lb (23-kg) front wheel weight(s) required (installation requires BM18101, mounting hardware kit).
NA - Not recommended for use on front mower.
NOTE: Ballast requirements may change. Always refer to the implement owner's manual for the appropriate ballast requirements.

Roll-Gard™ rollover protective structures protects operators of open-station mowers

ROPS (upright position)

ROPS (folded position)

The foldable two-post Roll-Gard rollover protective structure (ROPS) and retractable seat belt are standard equipment.

Foldable for trimming, such as when mowing under trees or bushes

Show More Show Less

Specifications

Select up to 4 models to compare specifications

John Deere

1550

TerrainCut™ Front Mower

Engine Manufacturer/model

3TNV80F

Engine Power

Gross PS: 25 hp
18.4 kW

Fuel tank capacity

16 U.S. gal.
60.6 L

Mower deck Size

60 or 72 in.
152 or 183 cm

Blade tip speed

18,000 fpm
5,486 m/min

Transmission

Hydrostatic 2WD, optional full time or on demand 4WD

Speed range

0-12 mph
0-19.3 km/h

Drive wheels

23x10.5-12
Optional: 23x8.5-12

Caster wheels

Flat free, 11x4-5

Warranty

24 months

Manufacturer/model

3TNV80F

Power

Gross
PS: 25 hp
18.4 kW

Rated engine rpm

3,000 rpm

Cylinders

Three

Displacement

77 cu in.
1.26 L

Maximum torque

At 1,900 rpm: 47.2 lb-ft
64 Nm

Injection

Indirect

Fuel type

Diesel (optional kit permits B20 compatibility)

Fuel tank capacity

16 U.S. gal.
60.6 L

Cooling

Liquid

Cooling capacity

7.5 U.S. qt
7.1 L

Air cleaner

Dual element dry type

Air restriction indicator

Standard

Charging system

Automotive type

Alternator, amp

75 amp

Battery

12 V

Transmission

Hydrostatic 2WD, optional full time or on demand 4WD

Speed and direction control

Two-pedal foot

Cruise control

Optional

Hi/Lo range

No, single speed transmission

Speed range

Hi forward

0-12 mph
0-19.3 km/h

Lo forward

Hi reverse

0-5 mph
0-8 km/h

Lo reverse

4-wheel drive

Differential lock

Final drives

PTO

PTO clutch

PTO drive output

Type

Open center

Pump capacity

5.1 U.S. gpm
19.3 L/min

Spool valve

Front lift, standard

Lift cylinders

Two

Type

Hydraulic cylinder

Turns lock-to-lock

2 maximum, 1.5 minimum

Type

Internal wet disk

Individual turn brakes

Standard

Master brake

Standard, locking

Warranty	24 months

Drive wheels

23x10.5-12
Optional: 23x8.5-12

Steering

2WD: 18x8.5-8
4WD: 18x8.5-10

Type	Optional hydraulic

Wheelbase

49.2 in.
125 cm

Ground clearance

6.5 in.
16.5 cm

Length

Less mower deck: 86.7 in.
220.2 cm

Overall width

Narrow Width 23x10.5 tires: 51.8 in.
131.6 cm
Wide Width 23x10.5 tires: 60.3 in.
153.2 cm

ROPS

Standard (folding)

ROPS certification

Two-post: OSHA 1928; Canadian Std.: CSA-352
Four-post: SAE J2194; EU Standard: 86/298/EEC; ISO 21299:2009

Overall height with ROPS

82.7 in.
210 cm

Overall height with ROPS folded

58 in.
147 cm

Shipping weight

Net weight, 2WD without mower or fuel: 1,675 lb
760 kg
Net weight, 4WD without mower or fuel: 1,835 lb
832 kg

Construction

One-piece stamped: 7-Iron PRO

Deck thickness

7 gauge
0.180 in.
4.6 mm

Size

60 or 72 in.
152 or 183 cm

Deck offset

Yes

Cutting height

1-6 in.
2.54-15.24 cm

Belt tensioning

Spring loaded

Blade tip speed

18,000 fpm
5,486 m/min

Caster wheels

Type
Flat free
Size
11x4-5

Front anti-Scalp rollers

Yes, gauge wheels

Rear anti-scalp rollers

Yes, gauge wheels

Shipping weight

Cutting width

62, 72 in.
157, 183 cm

Cutting height

1-6 in.
2.5-15.2 cm

Caster wheels

Type
Flat free
Size
11x4-5

Shipping weight

Offers and Discounts

1550TerrainCut™ Front Mower

SHARE

Features

Rear-mounted radiators

Fuel tank is large capacity with convenient gauge for maximum uptime

Rotate for Service (RFS™)

Heavy-duty blade spindles

60-in. (152-cm) 7-Iron PRO Side-Discharge Mower Deck

62-in. (157-cm) FastBack Mower Deck

72-in. (152-cm) 7-Iron PRO Side-Discharge Mower Deck

72-in. (183-cm) FastBack PRO Mower Deck

Mower deck specifications

PTO shaft drive is easy to access for quick-change of equipment

Tires are matched to the machine size and mower widths

1550, 1570, 1575 tires

1580, 1585 tires

Optional mulching kits add versatility to the mower decks

Tilt steering

Safety starting system helps protect the operator and others

Tilt steering and headlights are standard equipment

Brakes and differential lock are convenient to use for maximum productivity

12-V power outlet is convenient to use

Certification ensures compliance with safety standards

Overview

JDLink M Modem - 4G

John Deere Operations Center

Location and status

Engine hours

Maintenance planner

Machine Analyzer Tool

Fuel level

Diagnostic trouble codes (DTCs)

Service Advisor Remote

Compatibility

Engine hood

Quick response (QR) codes link to owner information web pages

Foot platform access panel

Trailering features are included to reduce the time and cost to move equipment

Remote battery posts

Durable design

Tail follows the trail

Maneuverability:

Specifications

Add Model

Key Specs

Engine

Drivetrain

Travel speed

Hydraulics

Steering

Brakes

Buyer's notes

Tires

Weight transfer

Dimensions

Mower decks

Mower deck (rear discharge)

Additional information

Offers and Discounts

Related Products

Shop and Buy

Maintenance and Support

You May Also Be Interested In